. . . . . . . . . . . . . . . . . . . . . . . . .
Medalist SL Family
. . . . . . . . . . . . . . . . . . . . . . . . .
540sl, 851sl
. . . . . . . . . . . . . . . . . . . . . . . . .
1080sl, 1270sl
. . . . . . . . . . . . . . . . . . . . . . . . .
ATA Interface Drives
. . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . .
Medalist SL Family Installation Guide, November 1995
1
Introduction
®
Thank you for choosing a Seagate drive. The purpose of this
guide is to assist you with installing your new hard drive. Its
organization outlines the complete installation process from han-
dling the drive in “Before you begin...” to offering troubleshooting
suggestions and technical support information. The topics dis-
cussed are:
•
•
•
•
•
•
•
Handling your drive (see “Before you begin...” on page 3)
Configuring the drive
Attaching cables to the drive
Mounting the drive
Configuring the computer
Troubleshooting
Where to call for Seagate technical support
Seagate provides installation software, EZ-Drive, and a 32-bit
disk access driver for Windows, SEG32BIT.386, that allows the
computer to surpass the 528-Mbyte barrier when it is imposed.
The software is stored on the drive and must be transferred to a
diskette in Drive A before you partition and format the drive. A
program called Seamove is provided to make the transfer easy.
We hope your installation goes smoothly, but if complications
arise, a list of common symptoms and solutions is provided in the
troubleshooting section. If the problem persists, contact your
dealer first. Your dealeris familiar with systemintegration and the
conflicts that may arise. If you need additional help or information
about Seagate products, numbers for Seagate technical support
services are listed on pages 34–36.
2
Medalist SL Family Installation Guide, November 1995
Drive features
Model
ST5540A ST5851A ST51080A ST51270A
Formatted Capacity
Mbytes
541
854.6
1,083
1,282
Cylinders
1,050
16
1,656
16
2,100
16
2,485
16
Heads
Sectors
63
63
63
63
Average seek time
Cache (segmented)
Spindle speed
External transfer rate
10.5 msec
128 Kbytes
5,376 RPM
16.61 Mbytes per second max.
3.51 Mbytes per second
Supported
Average sustained
transfer rate
LBA
Multiple block
read/write
Supported
PIO modes
0, 1, 2, 3, 4
0, 1, 2
Multiword DMA
Power-management
Data streaming
Supported
Supported
1. To achieve optimal performance, your computer must support PIO
mode 4 or multiword DMA mode 2. If these modes are not supported,
you can upgrade your system with a host adapter that supports them.
Ask your computer reseller for details.
Medalist SL Family Installation Guide, November 1995
3
Before you begin...
The drives in this manual are referred to by their model numbers:
ST5540A for the Medalist 540sl, ST5851A for the Medalist 851sl,
ST51080AfortheMedalist1080sl andST51270AfortheMedalist
1270sl.
Application. Your Seagate drive is designed for IBM AT and
compatible personal computers. It uses the ATA interface. It is
intended for use with UL-listed computers or similar products.
Drive handling. Your drive is vulnerable to damage from rough
handling and static discharge. Do not drop your drive. Do not
remove the seals and labels on the drive. The drive warranty is
voided if the seals and labels are removed.
Static discharge. Your drive contains components that can be
damaged by static discharge. Static damage can be cumulative
and may not manifest immediately. Observe these precautions:
•
Ground yourself before handling the drive. Wear a ground
strap that is properly connected to earth ground, or touch the
metal of a power supply that is plugged into a wall outlet while
handling the drive.
•
•
•
Keep the drive in its antistatic bag until you are ready to install
it. Do not attach any cables to the drive while it is in its bag.
Handle the drive gently and only by its edges or frame. Place
it on an antistatic surface until you are ready to install it.
Do nottouchthe drive’sconnectorpins orprintedcircuitboard.
Inspection. Use the handling precautions listed above when you
inspect the drive. If it appears to be damaged, call your distributor
or dealer immediately.
4
Medalist SL Family Installation Guide, November 1995
Warranty. Your drive comes with a three-year limited warranty.
Note. Withregardstothe EZ-DriveandSEG32BIT.386software,
there are no warranties, express or implied, including, but
not implied, warranties of merchantability or fitness for a
particular purpose. All such warranties are expressly and
specifically disclaimed.
Maintenance and repair. Seagate drives do not require mainte-
nance. The head/disc assembly is sealed; a broken seal voids
the warranty. Seagate customer service centers are the only
facilities authorized to repair Seagate drives. Seagate does not
sanction any third-party repair facilities.
Sicherheitsanleitung
1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umge-
bungstemperatur von 55°C vorgesehen ist.
2. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32
UNC-2A benötigt. Bei seitlicherBefestigungdarfdie maximale
Länge der Schrauben im Chassis nicht mehr als 3,3 mm und
bei Befestigung an der Unterseite nicht mehr als 5,08 mm
betragen.
3. Als Versorgungsspannugen werden benötigt:
+5V æ 5% 0,6A
+12V æ 5% 0,8A (1,9A fur ca. 30 Sek. fur æ 10%)
4. Die Versorgungsspannung muss SELV entsprechen.
5. Alle Arbeiten auf dem Festplatte dürfen nur von Ausgebilde-
tem Servicepersonal durchgeführt werden. Bitte schaffen Sie
Festplatteetiketten nicht weg.
6. Der Einbaudes Drives muss den Anforderungen gemäss DIN
IEC 950V DC 0805/05.90 entsprechen.
Medalist SL Family Installation Guide, November 1995
5
Warning. Turn off the computer before you remove its cover.
Turn off the power before you install or remove any
adapter card or the drive.
Caution. Special training or tools may be required to service
laptop computers. Removing the cover may void your
warranty. Review the terms and conditions of your
warranty before removing the cover.
Configuring the drive
Required materials:
•
2-mm jumper connector (supplied as spare jumpers)
Your Seagate drive is configured using the options jumper block
shown in Figure 1 on page 6. The option settings are shown in
Figure 2 on page 7. You can configure the drive:
•
•
•
For one- or two-drive operation.
To be the master or slave drive.
To operate as the master with drives that use a different
master/slave timing protocol.
•
•
For computers that use cable-select.
To use a remote drive-activity LED.
To configure the drive, attach a jumper to the pins on the options
jumperblockforthedesiredoption. Theconfiguration optionsare:
Spare jumper. Spare jumpers are provided on pins 2 and 4 and
on pins 6 and 8 for configuring your drive. These settings are not
used to configure the drive. The jumper is a 2-mm connector. If
you use a larger connector, you may damage the jumper-block
pins.
6
Medalist SL Family Installation Guide, November 1995
Options jumper block
pin 1
pin 1
Interface
connector
Standard
power connector
1
2
3
4
Circuit
board
+5V
+5Vreturn
+12Vreturn
+12V
Figure 1. Drive connectors
One-drive only.Use this configuration if thereare nootherdrives
attached to the hard disc controller.
Master with slave present. Use this configuration if the drive is
the first of two drives in your system. The master drive is Drive 0
in the System Setup record.
Slave. Use this configuration if the drive is the second drive in the
system. The slave is Drive 1 in the System Setup record.
Medalist SL Family Installation Guide, November 1995
7
5
6
11 9
7
3
4
1
2
Circuit
board
side up
12 10 8
Spares
One drive only
Drive is master;
slave is present
Drive is slave when
another drive is master
Master/slave timing protocol.
Drive waits up to 30
seconds for slave to
respond.
Cable select
Remote LED
connection
pin 11 (–), pin 12 (+)
Figure 2. Options jumper block settings
8
Medalist SL Family Installation Guide, November 1995
Master/slave timing protocol. This protocol involves the com-
munication between the computer and the disc drives during the
boot cycle only. The computer queries the master drive for the
status of both drives. The slave must report its status to the
master within a certain time period. If it does not respond, a
timeout error is issued and the computer does not identify the
slave. Place a jumper on pins 3 and 4 and on pins 5 and 6 to
extend the time period to 30 seconds that the Seagate master
waits for the slave to respond.
Cable-select. Use this configuration if your computer uses ca-
ble-select. Refer to your computer user’s manual.
Remote LED. Place the ground wire side of the remote drive-ac-
tivity LED connector, usually the black wire, on pin 11 (–) and the
otherside on pin 12 (+)of the options jumperblock. The LED may
be damaged if the cable is attached incorrectly.
Attaching the cables
Required materials:
•
•
A four-conductor power-supply cable
A 40-conductor interface cable with a 40-pin, female interface
connector for each drive you want to attach.
Note. To ensure the integrity of your data, use a nonshielded
cable with a maximum length of 18 inches (46
centimeters).
1. Attach the interface cable. Pin 1 on the drive must align with
pin 1ofthe hard-disc controller connector. Usethe edge-stripe
on the cable to denote pin 1. Pin 1 on the drive is located next
to the four-pin power connector.
Medalist SL Family Installation Guide, November 1995
9
Caution. The cable and connector bond is delicate. Pulling the
cable to remove the connector may damage the cable.
Attach an interface connector to the drive. If your interface con-
nector has a key, it will plug into the drive only one way. Make
sure that you do not bend the pins when you attach the cable.
Attach an interface-connector to the hard-disc controller connec-
tor on the motherboard or host adapter (see your system user’s
guide or host adapter user’s guide to determine the location of
pin 1). Make sure that pin 1 is aligned with pin 1 on the drive.
Cable-select installation: If your computer uses cable-select for
connection, refer to its user’s guide to determine which interface
connector is used for the master and which is used for the slave.
2. Attach a power-supply cable to the drive.
Power
cable
Pin 1
Cable
stripe
Figure 3. Attaching cables to the drive
10
Medalist SL Family Installation Guide, November 1995
Mounting the drive
Required materials:
•
Four 6-32 UNC-2A screws (not included)
The drive fits in a standard 3.5-inch bay and can be mounted in
any orientation. Position the drive so that the cables are not
strained or crimped. Secure itwithfourmounting screws not more
than 6 full turns (0.20 inches) into the drive frame (see Figure 4).
Caution. To prevent drive mounting-hole damage, use only the
type of screws specified.
This completes the hardware installation.
Figure 4. Mounting holes
Medalist SL Family Installation Guide, November 1995
11
Transferring the software from the drive
Required materials:
•
•
•
Diskette Drive A
A bootable, blank, 1.2-Mbyte or larger diskette for Drive A
A bootable diskette with the Format command
Recent developments in drive technology have pushed drive
capacities beyond the limits that many older computers using
DOS can address. Seagate provides software that allows these
computers to surpass the address limit and access your new
drive’s full capacity. The software is stored on the drive at the
factory and must be transferred to a diskette in Drive A before
you partition and format the drive. The files stored on the drive
include:
•
EZ-Drive. This is drive installation software that enables com-
puters with BIOSs that restrict the hard disc capacity to 528
Mbytes to surpass the 528-Mbyte barrier.
•
SEG32BIT.386. This is a 32-bit disk access driver to replace
the native Windows 32-bit disk access driver. It extends 32-bit
disk access support to drive capacities above 528 Mbytes,
multiple block read/write and PIO modes 3 and 4.
•
•
Seamove. This is a program that automatically copies the
software and README files to a bootable diskette in Drive A.
It removes the factory-installed partition and format when the
files are copied.
README. This is a text file that contains information about
the Seamove transfer program.
12
Medalist SL Family Installation Guide, November 1995
To transfer the software, you must put a blank, bootable diskette
into Drive A. To create a bootable diskette:
1. Insert your DOS diskette into Drive A.
2. Type format a: /s.
The drive reads the DOS diskette and prompts you to insert
the diskette you want to format into Drive A.
3. Insert the blank diskette. Press ENTER. When the format is
complete, you can transfer the installation software files to the
diskette.
To transfer the software files:
1. Boot the computer with the diskette to which you want to
transfer the software files.
2. Enterthe System Setup. (Refertoyourcomputeruser’s guide.
System Setup may be called Setup, BIOS Setup or CMOS
Setup.) If your computer uses an automatic setup system, go
to step 5.
3. Find the hard disc configuration in the System Setup screen.
4. Select drive type 2 for your new Seagate drive. If your com-
puter does not offer drive type 2, use the following values: 615
cylinders, 4 heads and 17 sectors.
Note. These are interim drive-type values that allow you to
access the drive for extracting the installation files.
5. Activate the prompt for the Seagate drive.
6. Type seamove and press ENTER.
This command transfers the files from the drive to the diskette
in Drive A. When the transfer is complete, the Seamove
program erases the files and the drive partition and reboots
Medalist SL Family Installation Guide, November 1995
13
the computer. The computer returns an invalid drive specifi-
cation error if you try to access the drive.
Caution. Do not write-protect the Seagate software diskette with
EZ-Drive. The EZ-Drive program writes important in-
formation back to the diskette during the installation.
Configuring the computer
Configuring the computer involves updating the computer’s Sys-
tem Setup records with the new drive’s translation geometry
(cylinder, head and sector information) and partitioning and for-
matting the drive. The translation geometry is kept on the CMOS
chip and is used by the BIOS to assign locations for the data on
the drive. Many older BIOSs place limits on the translation
geometry parameter values that do not allow it to assign data
locations for more than 528 Mbytes when DOS is used. If your
computer uses such a BIOS, it cannot access the full capacity of
your new drive.
This section covers the following issues involved with configuring
your computer:
•
How to determine whether your computer can access your
new drive’s full capacity
•
•
•
•
Solutions you can use to surpass the 528-Mbyte barrier
Installing the drive using the EZ-Drive software
Installing the drive using the Standard setup
Replacing the Windows 32-bit disk access driver
14
Medalist SL Family Installation Guide, November 1995
Determining whether your BIOS accepts more than
528 Mbytes
The following suggestions can help you to determine whether
your BIOS limits the drive capacity to 528 Mbytes.
•
If youare using a286or386computer, thenativeBIOScannot
recognize more than 528 Mbytes.
•
If the copyright date of the BIOS is earlier than 1994, the BIOS
probably will not recognize more than 528 Mbytes. The BIOS
copyright date, manufacturer and version number appear on
your screen at the beginning of power-on or reboot.
•
Install the drive using the Standard setup described on page
20. (Transferthe free software stored on the drive to a diskette
before you start the installation. See page 11 for transfer
instructions.)When the installation is complete, typedir d: for
the new drive, and check the number of bytes free. The
numbershouldbeclosetotheformattedcapacityofyour drive.
If the number is less than 528 Mbytes, you need to consider
some alternatives for surpassing the 528-Mbyte barrier. Some
alternatives are listed below.
Solutions for surpassing the 528-Mbyte barrier
•
Use the free installation software, EZ-Drive, that is stored on
the drive at the factory or equivalent software. Instructions for
transferring the software to a diskette are on page 11. Instruc-
tions for using EZ-Drive are on page 15.
•
•
Upgrade theBIOStoonethatsupports morethan528 Mbytes.
Such BIOSs incorporate logical block addressing (LBA) and
extended cylinder-head-sector (CHS) addressing.
Use a host adapter that supports more than 528 Mbytes.
Medalist SL Family Installation Guide, November 1995
15
Using the EZ-Drive installation software
Note. The EZ-Drive software is authorized for installation only
with the drive on which it is shipped.
EZ-Drive allows your computer to access your Seagate drive’s
full formatted capacity. It bypasses the BIOS during the boot
sequence and uses information it creates on Drive C to identify
the drive before DOS is loaded. During the installation, EZ-Drive:
•
•
•
Determines how many drives are installed
Enters a drive type in System Setup for the new drive
Modifies the Drive C boot record with translation geometry for
the new drive
•
•
•
Partitions and formats the new drive
Copies the boot files to the new drive if it is Drive C
Enables Maximum Overdrive, which enables read/write mul-
tiple in drives that have this feature. The Change Installed
Features option thatappearsin thedialog box whenthe format
is complete allows you to disable Maximum Overdrive.
EZ-Drive is easy and safe to use. You can choose the fully-auto-
matic installation, which puts a single partition on the drive, or you
caninstall the drivewith multiplepartitionsofequal size(seepage
18 for instructions on creating multiple partitions of unequal size)
and other custom features. Online help is available in the Select
Installation Type menu as Information Help.
If you already have a drive installed, EZ-Drive will not harm your
data unless you instruct it to override that drive’s partition and
format. EZ-Drive automatically arranges the drive-type position
in System Setup to reflect how you have set the drive jumpers.
16
Medalist SL Family Installation Guide, November 1995
Note. EZ-Drive is designed for DOS installations. It supports
Microsoft MS-DOS Version 5.0 or later.
EZ-Drive does not support:
•
•
•
•
•
Toshiba laptops, XT or Micro Channel computers
Non-ATA hard drives (SCSI, ESDI, MFM and RLL)
Some Local Bus adapters that use 32-bit mode
Some systems that have PIO mode 3 or 4 active
OS/2 and NT
Caution. Some older virus-detection programs may misidentify
the EZ-Drive information stored in conventional mem-
ory as a virus. If all 640 Kbytes ofconventional memory
are not free, such programs assume a virus is present
and clean and restore the memory. If this happens,
information about the EZ-Drive installed drive is de-
stroyed, and the computer cannotidentify the drive. Do
not use these programs.
Note. The Seagate version of EZ-Drive cannotinstall a non-Sea-
gate drive without a Seagate drive present.
1. Boot your computer with the Seagate software diskette. This
is a precaution to ensure that the EZ-Drive installation does
not conflict with any terminate-and-stay resident (TSR) pro-
grams that may be in memory.
2. Type ez and press ENTER.
3. Disregard the Notice dialog box. The EZ-Drive software is
authorized for installation only with the drive on which it is
shipped. Press ENTER to continue.
Medalist SL Family Installation Guide, November 1995
17
4. Locate the bottom box on the screen. The model number of
each drive EZ-Drive identifies is listed in this box. If a drive you
have installed is not listed or the drive order (Drive 0 is the
master, Drive 1 is the slave) is incorrect or there is a drive not
identified message, make sure the master and slave jumpers
are set correctly on the drives and the I/O and power cables
are properly connected.
Note. Other troubleshooting tips are available in the Information
Help menu.
Caution. Turn off your computer before resetting the jumpers or
removing the cables.
5. If the drives are correctly identified, select Select Fully Auto-
matic Installation in the Select Installation Type dialog box.
This creates a single partition and formats the drive.
If you are installing the drive as Drive C, EZ-Drive automat-
ically writes the system files to the drive to make it bootable.
6. When the format is complete, the Options dialog box appears.
Select and read Important Information. This instruction tells
you how retain the use of the EZ-Drive-installed drive when
you boot to Drive A.
7. Select Reboot to reboot the computer and save the installa-
tion. Remove the EZ-Drive diskette and put it away. Itcontains
information about the drive setup.
Toward the end ofthe bootsequence, yourscreen should display
a prompt for booting with a diskette followed quickly by the Micro
House banner and the C: prompt. If the boot prompt and the
banner fail to appear, your computer has not recognized the
EZ-Drive installed drive. Retry the installation.
18
Medalist SL Family Installation Guide, November 1995
Booting with a diskette after EZ-Drive is installed
When you boot with a diskette, you must allow the EZ-Drive
information aboutthe drive to loadinto memorybeforethe system
information on the diskette loads. The diskette accesses the
BIOS directly, which does not recognize the EZ-Drive-installed
drive. To boot your computer with a diskette:
1. Boot the computer with the diskette-drive door open.
2. Press the CTRL key when the following message appears near
the end of the boot sequence:
Hold the CTRL key down to boot from a floppy
3. Insert the boot diskette. The computer boots to Drive A.
Installing multiple partitions
The custom installation option in the installation menu allows you
to create up to nine partitions of equal size on the drive. To create
partitions of unequal size on your EZ-Drive installed drive, use
the FDISK and FORMAT commands on a DOS diskette. Refer to
your DOS manual if you need assistance deleting, creating and
formatting partitions. This instruction assumes you have already
installed the drive with EZ-Drive.
1. Boot your computer from Drive C.
2. Insert a bootable diskette that contains the FDISK and FOR-
MAT programs into Drive A and change the prompt.
3. Type fdisk.
Caution. If you have two drives, be sure you choose the
correct drive before deleting the partition. Deleting
the partition erases everything on the drive. Option
5 allows you to select the drive you want to use.
Medalist SL Family Installation Guide, November 1995
19
4. Select option 3 to delete the primary partition from the EZ-
Drive installed drive.
Note. EZ-Drive puts a volume label on the partition it creates.
You must enter the label name to delete the partition.
5. Repartition the drive in the partition sizes you want. Refer to
your DOS manual if you need assistance creating partitions.
Remember to make the Drive C primary partition active.
The computer will reboot when the partition process is complete.
However, you must make sure the EZ-Drive installed drive is
present to continue with the format. (The EZ-Drive banner ap-
pears when the drive is recognized.)
1. Remove the diskette while the computer reboots. Press the
CTRL key when the following message appears:
Hold the CTRL key down to boot from a floppy
The message is very quick and you may need to boot several
times before you succeed. (Some computers allow you to
press the CTRL key early.) If you get an Invalid OS error
message, the computer has not found the EZ-Drive installed
drive, and you must start the boot process again.
2. Reinsert the diskette.
3. Type format drive: for each partition you have created.
drive represents the letter assigned to the partition.
Note. DOS automatically assigns a letter to each partition.
Use the appropriate letter in the format statement.
If you are formatting Drive C, type format c: /s to make the
drive bootable.
4. Reboot the computer when you are done formatting.
20
Medalist SL Family Installation Guide, November 1995
Standard setup
If your computeracceptsthefullcapacityofthenewdrive, System
Setup must be configured to recognize the drive. Some comput-
ers automatically detect the new drive and configure System
Setup. This section tells you how to manually configure System
Setup. When the setup is complete, partition and formatthe drive.
1. Turn the computer on.
2. Enter System Setup. (Refer to your computer user’s guide.
System Setup may be called Setup, BIOS Setup or CMOS
Setup.)
3. Find the hard disc configuration in the System Setup screen.
4. Selectadrive type thatmatchesthe drivetranslation geometry
for your drive as shown in the table.
Translation geometry
CMOS
CHKDSK
Model
(Setup)
Mbytes2
Sectors
Mbytes3
Cyl
Heads
per track
ST5540A
ST5851A
ST51080A
ST51270A
541.9
854.6
1,050
1,656
16
16
16
16
63
63
63
63
517
815
1,083.8 2,100
1,282.4 2,485
1,034
1,223
Note. CHKDSK and CMOS capacities are approximations.
The capacities your computer reports may vary slightly.
2. One Mbyte equals 1,000,000 bytes.
3. One Mbyte equals 1,048,576 bytes.
Medalist SL Family Installation Guide, November 1995
21
Select the user-defined or custom drive-type option, if avail-
able, and enter your drive’s translation geometry.
If a user-defined drive type is not offered, select the drive type
with the largest translation geometry. This is the maximum
drive capacity your computer can recognize in its current
configuration. To access the full capacity of your drive, you
must upgrade your computer with a BIOS or host adapter
capable of accessing more than 528 Mbytes.
Note. Thedrivedoesnot usewriteprecompandlandingzone.
If these parameters are listed, make their values zero.
If you upgrade your system at a later date to achieve the
drive’s full capacity, youmustrepartition and reformatthedisc.
Be sure to back up your data first.
5. When you havecompletedsetting the translation geometry for
your drive, save the values and exit System Setup. Reboot
your computer. Partition and format the drive.
Partitioning and formatting the drive
Before you can use your Seagate drive, you must partition and
format it. In this guide we discuss partitioning and formatting your
drive with DOS—refer to your DOS user’s guide for assistance.
If you are using another operating system, consult your operating
system user’s guide for partitioning and formatting instructions.
Note. If you have not copied the free installation software to a
diskette, your computer will detect a partition on the drive.
You must erase this partition before you can access the
full drive capacity. When you transfer the files to a diskette
using Seamove (see page 11 forinstructions), the partition
is automatically erased when the transfer is complete.
22
Medalist SL Family Installation Guide, November 1995
Low-level formatting
The drive is low-level formatted at the factory using 512 bytes per
sector. Low-level formatting is not required.
Partitioning
You must partition the drive into one or more logical drives before
you can use it.
Caution. Partitioning or formatting a drive at any level erases all
data on it. Make a backup copy of your existing files on
another drive before you repartition or reformat. Sea-
gate assumes no liability if you erase your data.
You can partition a drive as follows:
1. Insert a bootable diskette into Drive A. Turn the computer on.
2. After the computer has completed booting, remove the boot
diskette from Drive A. Insert a diskette that has the FDISK
utility into Drive A and type fdisk. Press ENTER.
Note. If youhavetwodrivesinyoursystem,the menudisplays
five options. Option five allows you to select the drive
you want to partition. Make sure you select the correct
drive.
3. Selectcreate DOS partition orlogical DOS drive. Press ENTER.
4. Select create primary DOS partition. Use the maximum avail-
able size for your primary partition and make the partition
active for Drive C. This puts the entire drive on one partition
and allows you to load the DOS boot information on the drive.
Press ENTER for each subsequent selection.
After all of the appropriate selections are made, the computer
reboots itself. You must place a bootable diskette into Drive A.
Medalist SL Family Installation Guide, November 1995
23
High-level formatting
High-level formatting (henceforth referred to as formatting) builds
the file allocation table (FAT) DOS uses to access files on the
drive. If you put more than one partition on the drive, you must
format each partition. Use the DOS FORMAT utility to format the
drive as follows:
1. Type the following command at the DOS prompt:
format drive: /v /s
drive: designates the drive you are formatting. If you are
formatting the boot drive or if your system contains only one
drive, type c:. To format a second drive, type d:.
/v tells the computer to create a volume label for the partition
after it is formatted. Labeling can prevent someone from
accidentally deleting the partition and losing your data.
/s tells the computer to copy the system files to the drive to
make it bootable.
2. When the computer prompts you for a volume label, you can
assign a name to the drive volume of up to eleven characters
or leave it blank. Press ENTER.
Windows 32-bit disk access
If Windows enables the 32-bit disk access during its installation,
an error message appears when Windows loads after you have
installed a drive with more than 528 Mbytes. The Windows 32-bit
disk access driver must be turned off for you to open and use
Windows. Use the Seagate replacement driver, SEG32BIT.386,
to restore 32-bit disk access capability. To open Windows and
restore 32-bit disk access:
1. Press ENTER to open Windows.
24
Medalist SL Family Installation Guide, November 1995
2. Open the Main menu.
3. Open the Control Panel.
4. Open Enhanced.386.
5. Select Virtual Memory.
6. Select Change.
7. Select 32-Bit Disk Access at the bottom of the screen to
change its status.
8. Select OK. Follow the screen instructions to reboot.
You can re-establish the 32-bit disk access capability using the
SEG32BIT.386 software as follows:
1. Load Windows.
2. Open the Program Manager menu and select File.
3. Select Run.
4. Load the Seagate software diskette.
5. In the command line box, type: drive:stsetup
6. Read the license agreementthatappears onthe screen. Ifyou
agree to the terms, select ACCEPT AGREEMENT to continue.
7. The next screen lists the features the SEG32BIT.386 driver
supports. If your computer supports these features, they will
be active in 32-bit disk access mode with SEG32BIT.386 for
all drives that support them. Select Install Driver to continue.
8. Once the driver is installed, you must enable the 32-bit disk
access option in the Windows control panel to make it opera-
tional. You can choose to enable the option now or later. If you
choose to enable the driver now, the program opens the
Windows main menu. Repeat steps 3 through 7 to enable
SEG32BIT.386 32-bit disk access.
Medalist SL Family Installation Guide, November 1995
25
Basic troubleshooting
Warning. Always turn off the computer before changing jumpers
or unplugging cables and cards.
Caution. Your drive and computer contain static-sensitive de-
vices. Wear a ground strap or use other antistatic
precaution while handling your drive.
If you have installed your drive and it does not function properly,
perform the following basic checks:
•
Verify compatibility. Verify that the host adapter and the
drive are appropriately matched to each other and to your
computer. Refer to relevant documentation for details.
•
•
Check all cards. Verify that all cards are seated in their slots
on the motherboard and are secured with mounting screws.
Check all cables. Make sure all ribbon and power cables are
securely connected. Ribbon cables are easily damaged, es-
pecially at the connector. Try a new cable or a known good
cable. Make sure no socket pins were bent when the cable
was inserted. For each cable, verify that cable-connector pin
1 is aligned with equipment-connector pin 1. The edge-stripe
on the ribbon cable is used to denote pin 1.
Caution. Do not reverse-plug connectors. This will damage
your drive if the power is applied.
•
Verify equipment configuration. Review the instructions in
this guide and the host adapter installation guide and make
sure that all appropriate jumpers are installed, or removed, to
suit your application.
26
Medalist SL Family Installation Guide, November 1995
•
Check the power-supply specifications. If new devices are
installed, your computer’s power supply may not support the
new total power requirement. Consult your dealer.
•
Verify the drive type setting in System Setup. The drive-
type values used to configure System Setup must not exceed
the physical specifications of your drive (see the translation
geometry table on page 20). Also, if you have an older BIOS,
the translation geometry values must not exceed the limita-
tions set by the BIOS.
•
Check for viruses. Before you use someone else’s diskette
in your system for the first time, scan the diskette for viruses.
Advanced troubleshooting
If you have performed the preceding basic checks but the prob-
lemhasnotbeen solved, follow theseguidelines fortroubleshoot-
ing specific cases:
The system does not recognize the drive.
•
•
•
Check all cables.
Make sure the power supply is adequate for system needs.
Reboot the computer and make sure the drive motor runs. If
yourdrive is very quiet, itmay be difficult tohearits discs reach
operating speed. Recheck all drive cables if the drive is not
running.
•
•
Verify the SystemSetup drive type values. Each drive present
must be represented in System Setup.
Try a warm boot(arebootwithoutturning offcomputerpower).
To do this, press CTRL, ALT, and DELETE at the same time.
If the drive is recognized after the warm boot, the computer
Medalist SL Family Installation Guide, November 1995
27
BIOS’ setup test may be completing before the drive is ready.
One possible solution is to slow your computer’s processor
speed during startup. If your computer has a turbo switch, set
it to slow speed before turning the computer on. If there is no
turbo switch, you may be able to use keyboard commands to
slow the processor speed; see your computer manual for
details. After the computer is up and running, return the
processor to the fast speed.
Another solution is to warm-boot your computer after every
power-on.
•
Check for I/O address conflicts. To isolate the conflict, first
verify that the drive and host adapter are compatible with your
computer by removing all the peripheral adapter cards (power
must be off) except for the video card. Then reinstall the drive
and host adapter card. If this is successful, reinstall the other
peripherals one at a time until the conflict reoccurs.
After you have isolated the source of the address conflicts,
you can resolve the conflictby changing theI/Oaddress of the
peripheral that appears to cause the conflict.
•
•
If yourdrivewasinstalled with EZ-Drive, thespecial instruction
in the boot sequence on Drive C may have been bypassed.
Remove the diskette and reboot. The section “Booting with a
diskette after EZ-Drive is installed” on page 18 describes how
to boot with a diskette.
If the computer does not recognize the slave drive following
power-on, the slave may not be communicating with the
master during the boot cycle. Try reconfiguring the mas-
ter/slave timing protocol jumpers discussed on page 8.
28
Medalist SL Family Installation Guide, November 1995
The dealer partitioned and high-level formatted the drive for
you in the store. Later, you installed the drive and it does not
respond.
•
•
•
•
Reboot the computer and make sure the drive spins up.
Check all cables.
Make sure the power supply is adequate for system needs.
Use the same version of DOS within all partitions. Make sure
the DOS version the dealer used to partition and format the
drive is the same as the version you installed on your com-
puter. If it isn’t, see your dealer.
•
Verify the System Setup drive type value. You must install the
drive using the same drive type or translation geometry that
your dealer used to partition the drive.
•
•
Check for I/O address conflicts between peripheral cards.
Check for viruses.
The screen remains blank when you power up the system.
•
•
Make sure the monitor is plugged in and turned on.
Check all cards. Make sure the video card is seated in its slot
and secured with mounting screws.
•
•
Check all cables. Make sure the video-card cables are se-
curely attached.
While the computer is powered down, remove the drive host
adapter. If the screen turns on after you reboot, the host
adapter may be incompatible or defective. If so, see your
dealer.
Medalist SL Family Installation Guide, November 1995
29
The system hangs in FDISK or fails to create or save the
partition record.
•
•
Check all cables.
The DOS utilities diskette may be corrupted. Try your backup
DOS diskette.
•
•
Make the partitions smaller.
Tryanother drivetypeortranslationgeometry.Thecomputer’s
BIOS may not accept a particular translation geometry for
writing into the CMOS setup memory.
•
•
Change the interrupt jumper setting on the host adapter.
Check for media defects at the beginning of the drive. Use a
third-party surface scan utility.
•
Some BIOSs have a Track 0 protection feature that protects
Track 0 from viruses. This can cause FDISK to hang the
system. You must disable this feature in System Setup before
you can use FDISK. See your computer reference guide for
assistance. Be sure to re-enable this important feature when
FDISK is done.
System error message, “Drive not Ready,” appears.
•
Check all cable connections. Foreach ribbon cable, verify that
pin 1 of the cable is matched to pin 1 of the connector. Pin 1
is usually denoted by the edge-stripe on the ribbon cable.
•
•
Make sure the power supply is adequate for system needs.
Reboot the computer and make sure the drive spins up.
The FDISK error message, “No Fixed Disk Present,” appears.
•
•
Check all cables.
Make sure the power supply is adequate for system needs.
30
Medalist SL Family Installation Guide, November 1995
•
•
•
Reboot the computer and make sure the drive spins up.
Verify the System Setup drive type values.
Check for I/O address conflicts.
The drive does not format to full capacity.
•
Verify your computer’s System Setup drive-type values. One
of the following problems may have occurred: 1) the values
may be set for an incorrect drive type or translation geometry;
2)you may have entered a parametervalue that exceeded the
physical capacity of the drive; 3) you selected a translation
geometry or drive type that does not take full advantage of the
drive’s capacity; or 4) the drive’s physical specifications ex-
ceed the translation geometry limits imposed by the BIOS.
Refer to “Standard setup” on page 20 if any of these cases is
true.
If you reset the System Setup drive-type value, you must
partition and high-level format the drive again.
•
•
•
If you partitioned the drive into individual logical drives, you
may need to make the partitions smaller so that the computer
can use all of the drive’s capacity.
If your computer supports LBA mode, you may need to enable
an LBA mode function in System Setup to get the drive’s full
capacity. Refer to your computer’s reference guide.
You can use the EZ-Drive software to install the drive.
DOS messages “Disk Boot Failure,” “Non-System Disk,” or
“No ROM Basic - SYSTEM HALTED,” appear.
•
•
Reinstall the DOS system files using the DOS SYS utility.
Check all cables.
Medalist SL Family Installation Guide, November 1995
31
•
•
Use FDISK to verify that the primary partition is active.
Check for viruses.
System error message, “HDD controller failure,” appears.
•
•
Confirm the jumper settings on the drive.
Verify the System Setup drive type values.
The error message “Microsoft Windows 32-bit disk driver
(WDCTRL) phase 03, 3f” appears when you open Windows.
•
A device conflict occurs between the native Windows 32-bit
diskaccess driverand drives that havecapacities greater than
528 Mbytes. To get the advantages of 32-bit disk access and
more, install the SEG32BIT.386 32-bit disk access driver.
Installation instructions are on page 23.
Disabling EZ-Drive
Required materials:
•
•
A bootable diskette
A diskette that has FDISK. EXE
To disable EZ-Drive, use the DOS utility FDISK/MBR. This utility
replaces the EZ-Drive boot information on Drive C with the DOS
master boot record. The DOS master boot record uses the
information in System Setup to access the drive. Your computer
will stop accessing EZ-Drive-installed drives that are larger than
528 Mbytes. To access your drive’s full capacity, you must
reconfigure System Setup with the translation geometry shown
for your drive in the table on page 20. You must also partition and
format your drive.
Caution. Partitioning and formatting erases the data on the
drive. Back up your data before you disable EZ-Drive.
32
Medalist SL Family Installation Guide, November 1995
1. Turn the computer off.
2. Insert a bootable diskette into Drive A and turn the computer
on. Your computer must boot to Drive A without loading
EZ-Drive into the system memory.
3. When the boot cycle is complete, place a diskette that has the
FDISK utility in Drive A.
4. Type fdisk/mbr and press ENTER. This command erases the
EZ-Drive-modified master boot record on Drive C and re-
places it with the standard DOS master boot record. The
computer can no longer identify drives that have capacities
greater than 528 Mbytes installed using EZ-Drive. You must
partition and format the drive to make it accessible (see
Partitioning and formatting the drive on page 21).
Disabling Maximum Overdrive
Maximum Overdrive enables the drive’s read/write multiple fea-
ture. You can disable Maximum Overdrive during the installation
process or anytime afterward.
To disable it during the installation, select the Change Install
Features option in the Options dialog box that appears when the
format completes. This feature allows you to enable or disable
Maximum Overdrive.
To disable it after the drive has been installed:
1. Insert the Seagate software diskette with EZ-Drive into the
diskette drive.
2. Type ez at the command line.
3. Go to the Main menu and select Installation Options. Press
ENTER.
4. Select Change Install Features and press ENTER.
Medalist SL Family Installation Guide, November 1995
33
5. Select Disable Maximum Overdrive.
6. Press the ENTER key to change the status.
7. Usethe down-arrow keyto selectSaveChanges. PressENTER
to save.
Additional EZ-Drive troubleshooting and help information is avail-
able when you select Information Help in the main menu. An-
swers to frequently asked troubleshooting questions are
available in the EZ-HELP.EXE file on the diskette.
34
Medalist SL Family Installation Guide, November 1995
Technical support services
If you need assistance installing your drive, consult your dealer.
Your dealer is familiar with system configurations and can help
you with system conflicts and other technical issues.
If you need additional assistance with your Seagate drive orother
®
®
Sea
,
Seagate products, you can call SeaBOARD ,
FAX Sea-
gate Technical Support FAX, SeaFONE® or SeaTDD . Seagate
technical support information is also available on CompuServe
and through the Internet.
SeaBOARD
Using a modem, you can access documentation, drive specifica-
tions and jumper settings for Seagate’s entire product line. You
can also download software for installing and analyzing your
drive.
SeaBOARD is available 24 hours daily. It supports communica-
tions up to 9,600 baud. Set your communications software to
eight data bits, no parity and one stop bit (8-N-1). SeaBOARD
phone numbers are listed in the following table.
Location
United States
England
Modem number
408-438-8771
44-1-62-847-8011
(+33 1) 48 25 35 95
49-89-140-9331
65-292-6973
France
Germany
Singapore
Medalist SL Family Installation Guide, November 1995
35
Location
Thailand
Australia
Korea
Modem number
662-531-8111
61-2-756-2359
82-2-556-7294
SeaFAX
You can use a touch-tone telephone to access Seagate’s
automated FAX system to receive technical support informa-
tion by return FAX. This service is available 24 hours daily.
Location
Telephone number
408-438-2620
United States
England
44-1-62-847-7080
Seagate Technical Support FAX. 408/438-8137
You can FAX questions or comments to technical support
specialists 24 hours daily. Responses are sent between
8:00 A.M. and 5:00 P.M. (Pacific time) Monday through Friday.
SeaFONE. 408/438-8222
You can talk to a technical support specialist between
8:00 A.M. and 5:00 P.M. (Pacific time) Monday through Friday.
SeaFONE provides recorded technical information on se-
lected Seagate products while you are on hold. You can
access the recordings 24 hours daily. Before calling, note your
system configuration and drive model number (STxxxx).
36
Medalist SL Family Installation Guide, November 1995
SeaTDD. 408/438-5382
Using a telecommunications device for the deaf (TDD), you
cansendquestions or comments24hoursdailyandexchange
messages with a technical support specialist between 8:00
A.M. and 5:00 P.M. (Pacific time) Monday through Friday.
Seagate CompuServe forum
Online technical support for Seagate products is available on
CompuServe. To access our technical support forum, typego
seagate. This forum provides information similar to that found
on SeaBOARD.
Seagate’s Internet connections
Technical information for Seagate drives is available on the
internet from Seagate’s World Wide Web home page
similar to that found on SeaBOARD.
Medalist SL Family Installation Guide, November 1995
37
Storing and shipping your drive
Keep your original box and packing materials for storing or
shipping your drive. The box has a Seagate Approved Package
label. Shipping a drive in an unapproved container voids the
warranty. Call your authorized Seagate distributor to purchase
additional boxes.
The following figure shows how a drive fits in an approved
single-pack box, including the packing materials.
Foam
Antistatic bag
Drive
Foam
Figure 5. A drive in an approved package
Seagate Technology, Inc.
920 Disc Drive, Scotts Valley, CA 95066, USA
Publication Number: 36342-101, November 1995, Printed in USA
|
Toshiba 1 Tb 35" Internal Hard Drive Dt01aca User Manual
Sony Ericsson T258C User Manual
Sony 1261 4434 User Manual
Seagate ST905004EXD101 RK User Manual
Seagate BARRACUDA ST380815AS User Manual
RCA RP 7953 User Manual
PYLE Audio PDCD610MU User Manual
PQI Mr Flash U191 User Manual
Philips KPATKOE PYKOBOACTBO 10FF3CDW User Manual
Philips GoGear SA018102 User Manual